Effect of Electrode Type and Current Strength on the Mass of Substance Reduced at the Cathode in the Electrolysis Process

Authors

  • Jam'an Fahmi Universitas Negeri Medan https://orcid.org/0000-0001-6703-1782
  • Dwi Sapri Ramadhan Universitas Negeri Medan
  • Dian Wardana Universitas Negeri Medan
  • Wulan Dwi Safitri Universitas Negeri Medan
  • Moondra Zubir Universitas Negeri Medan
  • Nurdin Siregar Universitas Negeri Medan
  • Riska Greselia Manullang Universitas Negeri Medan
  • Novitri Yolanda Sagala Universitas Negeri Medan
  • Desy Meriani Br Sipahutar Universitas Negeri Medan

DOI:

https://doi.org/10.24114/ijcst.v8i2.70607

Keywords:

electrolysis, electrode materials, current strength, hydrogen production

Abstract

This study investigates the effect of electrode type and current strength on the mass of hydrogen gas produced at the cathode during the electrolysis of sodium chloride solution. A simulation based on Faraday’s law was conducted using three electrode materials—carbon, copper, and zinc—under controlled current settings of 0.10 A, 0.20 A, and 0.30 A for a fixed electrolysis duration of 30 minutes. Current efficiency values were assigned to each electrode to model realistic performance differences, with copper exhibiting the highest efficiency, followed by zinc and carbon. The results show that increasing the current leads to a linear rise in the mass of hydrogen produced for all electrode types, confirming the proportional relationship between electric charge and cathodic reduction predicted by Faraday’s law. Additionally, copper electrodes produced the highest hydrogen yield at all current levels, while carbon generated the lowest, indicating that electrode characteristics influence electrochemical efficiency. Overall, the findings demonstrate that current strength is the dominant factor determining the mass of reduced species at the cathode, whereas electrode material provides a secondary yet significant contribution to electrolysis effectiveness.

References

1. Hermayantiningsih D, Yuliana (2023) Studi Penggunaan Beda Potensial Pada Elektrodeposisi Ion Tembaga ( II ). J Cendekia Kim 01, 81–86.

2. SimioNeScu-Bogatu N, BeNea L (2022) Effect of the Applied Current Density and Deposition Time on Electro-Codeposition Process of Cobalt Matrix Reinforced with Nano-CeO2. Arch Metall Mater 67, 615–622.

3. Kaensakol R, Srisiriwat A, Srisiriwat N (2024) The analysis of electrode material efficiency in hydrogen production through electrolysis from seawater solution. PRZEGLĄD ELEKTROTECHNICZNY 45–48.

4. Mahesi TZ, Saputra R, Febriana I, A SE (2025) Pengaruh Jumlah Sel Elektroda Terhadap Produksi Gas Hidrogen dengan Proses Elektrolisis sebagai Sumber Energi Fuel Cell. J Tek Kim USU 14, 10–18.

5. Triandarto F, Mardyanto MA (2020) ELEKTROLISIS UNTUK MENURUNKAN LOGAM BERAT Cu THE EFFECT OF CURRENT AND VOLTAGE TO REMOVE. J Purifikasi 6, 175–180.

6. Zhang L, Lv M, Zhang H, Zhang X, Zhao M, Zhang M (2025) The Effect of Current Density and Cathode Position on the Corrosion Resistance and Thermal Emission Properties of Nickel Electroplated Layers on Brass Surfaces. coating 15, 1–12.

7. Hur J, Lee S, Ryu JS (2024) Effects of electrode configuration on the current density distribution of the electrolytic reducer. Nucl Eng Technol 56, 4951–4958.

8. Siregar MA, Umurani K, Damanik WS (2020) Pengaruh jenis katoda terhadap gas hidrogen yang dihasilkan dari proses elektrolisis air garam. UM-Tapsel Press 21, 57–65.

9. Rudnik E, Włoch G, Walkowicz M (2024) Effect of Electrolysis Conditions on Electrodeposition of. molecules 29, 1–22.

10. Tribbia M, Glenneberg J, Mantia L, Zampardi G (2024) Effect of the Current Density on the Electrodeposition Efficiency of Zinc in Aqueous Zinc-Ion Batteries. ChemElectroChem 202300394, 1–9.

11. Akhlaqi MB, Meryanilnda, Ariyanto P (2025) Pengaruh Konsentrasi Larutan Elektrolit dan Tegangan Arus Listrik terhadap Proses Electrorefining Tembaga. JURITEK J Ilm Tek Mesin, Elektro dan Komput 5, 125–136.

12. Lu S, Sun X, Zhang B, Wu J (2024) Review of Cathode Plasma Electrolysis Treatment : Progress , Applications , and Advancements in Metal Coating Preparation. Materials (Basel) 17, 1–26.

13. Ridzkiansyah RDM, Irwan Y (2021) Analisa Pengaruh Jenis Elektroda Pengelasan SMAW Pada Penyambungan Baja ASTM A36 Dengan Baja Tahan Karat AISI 304 Terhadap Sifat Mekanis. E-Journal Politek Negeri Lhokseumawe 1, 1–6.

14. Rifaldi Z, Mulyanti J (2021) ANALISIS PENGARUH VARIASI ELEKTRODA TERHADAP KEKUATAN TARIK DAN STRUKTUR MIKRO SAMBUNGAN LAS SMAW PADA BAJA ST 37. E-Journal Univ Janabadra 4, 1–5.

15. Ramadhan ML (2024) Elektrolisis. Polyg J Ilmu Komput dan Ilmu Pengetah Alam 2, 105–112.

Downloads

Published

2025-08-29

Issue

Section

Articles